Manual Page Search Parameters
PFLOGD(8) System Manager's Manual PFLOGD(8)

pflogd — packet filter logging daemon

pflogd [-Dx] [-d delay] [-f filename] [-i interface] [-s snaplen] [expression]

pflogd is a background daemon which reads packets logged by pf(4) to a pflog(4) interface, normally pflog0, and writes the packets to a logfile (normally /var/log/pflog) in tcpdump(8) binary format. These logs can be reviewed later using the -r option of tcpdump(8), hopefully offline in case there are bugs in the packet parsing code of tcpdump(8).

pflogd closes and then re-opens the log file when it receives SIGHUP, permitting newsyslog(8) to rotate logfiles automatically. SIGALRM causes pflogd to flush the current logfile buffers to the disk, thus making the most recent logs available. The buffers are also flushed every delay seconds.

If the log file contains data after a restart or a SIGHUP, new logs are appended to the existing file. If the existing log file was created with a different snaplen, pflogd temporarily uses the old snaplen to keep the log file consistent.

pflogd tries to preserve the integrity of the log file against I/O errors. Furthermore, integrity of an existing log file is verified before appending. If there is an invalid log file or an I/O error, logging is suspended until a SIGHUP or a SIGALRM is received.

The options are as follows:

Debugging mode. pflogd does not disassociate from the controlling terminal.
delay
Time in seconds to delay between automatic flushes of the file. This may be specified with a value between 5 and 3600 seconds. If not specified, the default is 60 seconds.
filename
Log output filename. Default is /var/log/pflog.
interface
Specifies the pflog(4) interface to use. By default, pflogd will use pflog0.
snaplen
Analyze at most the first snaplen bytes of data from each packet rather than the default of 160. The default of 160 is adequate for IP, ICMP, TCP, and UDP headers but may truncate protocol information for other protocols. Other file parsers may desire a higher snaplen.
Check the integrity of an existing log file, and return.
expression
Selects which packets will be dumped, using the regular language of tcpdump(8). Tcpdump has been extended to be able to filter on the pfloghdr structure defined in <net/if_pflog.h>. It can restrict the output to packets logged on a specified interface, a rule number, a reason, a direction, an IP family or an action.

ip
Address family equals IPv4.
ip6
Address family equals IPv6.
ifname kue0
Interface name equals "kue0".
on kue0
Interface name equals "kue0".
ruleset authpf
Ruleset name equals "authpf".
rulenum 10
Rule number equals 10.
reason match
Reason equals match. Also accepts "bad-offset", "fragment", "short", "normalize", "memory", "bad-timestamp", "congestion", "ip-option", "proto-cksum", "state-mismatch", "state-insert", "state-limit", "src-limit", and "synproxy".
action pass
Action equals pass. Also accepts "block" and "match".
inbound
The direction was inbound.
outbound
The direction was outbound.

/var/log/pflog
Default log file.

Log specific TCP packets to a different log file with a large snaplen (useful with a "log all" rule to dump complete sessions):

# pflogd -s 1600 -f suspicious.log port 80 and host evilhost

Log from another pflog(4) interface, excluding specific packets:

# pflogd -i pflog3 -f network3.log "not (tcp and port 23)"

Display binary logs:

# tcpdump -n -e -ttt -r /var/log/pflog

Display the logs in real time (this does not interfere with the operation of pflogd):

# tcpdump -n -e -ttt -i pflog0

Display the logs in real time of inbound packets that were blocked on the wi0 interface:

# tcpdump -n -e -ttt -i pflog0 inbound and action block and on wi0

pcap_open_live(3), pf(4), pflog(4), pf.conf(5), newsyslog(8), tcpdump(8)

The pflogd command appeared in OpenBSD 3.0.

pflogd was written by Can Erkin Acar <canacar@openbsd.org>.

August 30, 2019 openbsd